High Pressure, High Repeatability Mass Flowmeters for Clean Gases - Discontinued

FMA-8500

Up to ±1% Full Scale Accuracy
±0.25% of Rate Repeatability
316 SS Wetted Parts
Low Pressure Drop
For Clean, Non-Coating Gases up to 4500 psig

Beschreibung

This flowmeter is precise and sophisticated. It must be accurately calibrated for application conditions. If in doubt, consult OMEGA’s Flow Department.

OMEGA™ FMA-8500 Series high pressure mass flowmeters feature a superior ±0.25% repeatability for accurate measurement and control of gas flow. The flow sensor produces a 0 to 5 Vdc output signal linear to the mass flow rate for use in recording, indicating, or control purposes. The FMA-8500 Series controllers operate similarly to those in the FMA-7000E Series.

SPECIFICATIONS
Accuracy: ±1% full scale at 16 to 27°C (60 to 80°F) and 10 to 40 psig; ±2% full scale at 4 to 38°C (40 to 100°F) and 5 to 150 psig
Repeatability: ±0.25%
Time Constant: Three seconds to reach 98% of final value
Max Pressure:Up to 4500 psi at 66°C (150°F)
Pressure Drop: 10" water, max
Ambient Temperature Range: 4 to 66°C (40 to 150°F)
Output: 0 to 5 Vdc into 1000 Ω min load; 3 mV rms max ripple
Power: ±15 Vdc; 0.6 W max power consumption
Fittings: ¼" 316 SS compression fitting O-Rings/Gaskets: PFA
Transducer Assembly: 316 SS
Leak Rate: 10^-9 atm/cc-Helium
Pressure Coefficient: 0.03% shift within ±200 psig of the calibrated pressure

Range

Model No.	Range
FMA-8500-(*)	0 to 10 SCCM
FMA-8501-(*)	0 to 20 SCCM
FMA-8502-(*)	0 to 50 SCCM
FMA-8503-(*)	0 to 100 SCCM
FMA-8504-(*)	0 to 200 SCCM
FMA-8505-(*)	0 to 500 SCCM
FMA-8506-(*)	0 to 1000 SCCM
FMA-8507-(*)	0 to 2000 SCCM
FMA-8508-(*)	0 to 5000 SCCM
FMA-8509-(*)	0 to 10 SLM
FMA-8510-(*)	0 to 20 SLM

(*) You must specify gas, temperature and inlet/output pressure when ordering.

1) Select the core part number from the range code table above.
2) Add the gas, temperature and inlet/output pressure information after the core p/n, eg.: FMA-8501-Nitrogen, 70F, 20/0 psig (This is a FMA-8501 0 to 20 SCCM, flowmeter for nitrogen, operating at 70F, with an inlet pressure of 20 psi, and outlet pressure of 0 psi)
3) Enter the Constructed part number in the "Order Specific Models Here" table below!
4) You will then add the p/n to your cart and check out with a non-std p/n.
5)We will confirm by email and/or telecon price and availability after the order is placed.

*Alle Preisangaben in Euro.
Anmerkung: For calibraton above 200 psig, add $450.00 to price. For NIST calibration add "-NIST" to the part number and $425.00 to the price. NIST calibration does not include points.

All models are custom, consult specification page for complete description and list of available models.